Emerson 3051S Dokumentacja Strona 75
- Strona / 188
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
49
Reference Manual
00809-0100-4803, Rev DA
Section 3: Configuration
April 2013
Configuration
3.7.2 Energy rate
(Fully Compensated Mass and Energy Flow Feature Board only):
Note
Energy Rate calculations are only available for certain fluid types.
The Energy tab allows the user to configure the settings associated with the energy flow.
1. Under the Energy Rate Setup heading, edit the Energy Rate Units and Damping values as
needed. The energy rate calculation within the device uses undamped process
variables. Energy rate damping is set independently of flow rate damping and measured
process variables.
2.Under the Custom Units Setup heading, the user may configure a custom unit for the energy
rate measurement. Custom units allow the energy rate to be displayed in units of
measure that are not standard in the 3051S MultiVariable.
Note
If the energy rate is configured as the primary variable and is being output via the 4-20 mA
signal, verify the 4-20 mA range (LRV and URV) after completing the custom unit configuration.
For more information on verifying the 4-20 mA range, see “Basic device configuration” on
page 31.
Follow these steps to configure a custom unit:
a. Custom Unit: Enter the desired custom unit label to be displayed for the energy rate. Up
to five characters including letters, numbers, and symbols can be entered in the
custom unit field.
Note
It is recommended that the Custom Unit be entered in upper case letters. If lower case letters
are entered, the LCD will display upper case letters. Additionally, the following special
characters are recognized by the LCD Display: hyphens (“-”), percent symbols (“%”), asterisks
(“*”), forward slashes (“/”) and spaces. Any other character entered for the Custom Unit will be
displayed as an asterisk (“*”) on the LCD Display. The following warning will be returned
indicating these changes: “Custom Unit contains characters that will display in upper case or
asterisks on LCD. The DCS will display as entered.”
b. Base Unit: From the drop-down menu, select a base unit to be used for the custom unit
relationship.
c. Base per Custom: Enter a numeric value that represents the number of base units per
one custom unit. The 3051S MultiVariable transmitter uses the following convention:
Base per Custom =
Mass and Energy Flow Fast Keys 1, 4, 1, 2
Number of Base Units
1xCustomxUnit
-----------------------------------------------------------------------
- Rosemount 3051S MultiVariable 1
- Transmitter 1
- Contents 5
- Table of Contents 6
- 5Section 5: Troubleshooting 7
- Section 1 Introduction 9
- 1.2 Models covered 10
- 1.3 Service support 10
- Section 2 Installation 11
- 2.2.1 Warnings 12
- 2.4 Installation procedures 13
- 2.4.2 Mounting considerations 14
- LCD display rotation 15
- Feature board side of housing 15
- Cover installation 15
- Conduit entry threads 15
- Cover jam screw 16
- Process flange orientation 16
- 2.4.3 Mount the transmitter 17
- Flange bolts 18
- Mounting requirements 19
- 2.4.4 Process connections 20
- ROSEMOUNT 3051S / 3051 / 2051 21
- Impulse piping considerations 22
- Surges/transients 25
- Signal wire grounding 26
- 2.4.7 Grounding 27
- 305 INTEGRAL 29
- COPLANAR 29
- 305 INTEGRAL TRADITIONAL 29
- 304 TRADITIONAL 29
- 304 WAFER 29
- Section 2: Installation 34
- Installation 34
- Section 3 Configuration 35
- 3.2 Safety messages 36
- Connecting to a PC 38
- 3.4 Flow configuration 39
- Online and offline mode 40
- 3.4.4 Preferences 42
- 3.4.6 Fluid properties 46
- 3.4.8 Save / send 49
- Saving a configuration 51
- Sending a saved configuration 51
- Natural gas 52
- Custom gas 54
- Custom liquid [Density (T)] 55
- Units of measure 57
- 3.6.1 Model identification 60
- 3.6.2 Alarm and saturation 60
- 3.6.3 Variable mapping 62
- 3.6.4 LCD display 63
- 3.6.5 Communication setup 64
- Burst mode 65
- Enabling burst mode 65
- Choosing a burst option 66
- Multidrop communication 66
- Loop current mode 67
- 3.7 Variable configuration 69
- Time conversion example: 73
- 3.7.2 Energy rate 75
- Energy conversion example: 77
- Section 3: Configuration 79
- Configuration 79
- 3.7.3 Totalizer 81
- Totalizer conversion example: 83
- 3.7.4 Differential pressure 84
- 3.7.5 Static pressure 85
- 3.7.6 Process temperature 86
- 3.7.7 Module temperature 87
- 3.7.8 Analog output 88
- (page 1) 91
- (page 2) 92
- 3.8.5 475 Fast keys 95
- Function Fast Key Sequence 96
- 4.1 Overview 99
- 4.2 Safety messages 100
- 4.3 Transmitter calibration 101
- 4.3.2 Sensor trim overview 102
- Zero trim 103
- Upper and lower sensor trim 103
- Calibration type 104
- Recall factory trim 104
- Last DP sensor trim point 104
- 4.3.6 Analog calibration 108
- Analog output loop test 109
- 00809-0100-4803, Rev DA 110
- April 2013 110
- 4.5 Process variables 111
- 4.5.2 All variables tab 112
- Field device labels 113
- Remove the feature board 114
- Black Rubber V-Seal 115
- 4.6.3 Terminal block 116
- 4.6.4 LCD display 117
- 4.6.5 Flange and drain vent 117
- 4.6.6 SuperModule assembly 119
- Reference Manual 120
- Operation and Maintenance 120
- Section 5 Troubleshooting 121
- Section 5: Troubleshooting 122
- Troubleshooting 122
- Symptom Corrective Actions 124
- Symptom Corrective Action 128
- Reference Data 131
- Total performance 132
- Long term stability 133
- Warranty 133
- Ambient Temperature effect 134
- Line Pressure effect 135
- Mounting Position Effects 135
- Vibration effect 135
- Power supply effect 136
- Range and sensor limits 137
- 4–20 mA/HART 138
- Overpressure limits 139
- Static Pressure limit 139
- Burst Pressure limits 140
- Temperature limits 140
- Humidity limits 140
- Volumetric displacement 141
- Failure mode alarm 141
- A.1.3 Physical specifications 142
- Sensor module fill fluid 143
- Cover O-rings 143
- A.2 Dimensional drawings 145
- Pipe Mount Panel Mount 146
- Appendix A: Reference Data 147
- 3.56 Max open 148
- (90 Max open) 148
- A.3 Ordering information 149
- 2-14 NPT flange adapter ★ 152
- 2 SST flange adapter 152
- A.4 Accessories 157
- A.5 Exploded view diagram 158
- A.6 Spare Parts 159
- North American certifications 166
- European certifications 166
- Japanese certifications 167
- INMETRO certifications 168
- China (NEPSI) certifications 168
- IECEx certifications 169
- B.5 Installation drawings 171
- Product Certifications 172
- B.5.3 GE / GM option NEMA 4X 181
Powiązane produkty i podręczniki dla Pomiary, testowanie i kontrola Emerson 3051S
(4 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.052 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji