Emerson MICRO MOTION 2700 Instrukcja Instalacji Strona 107
- Strona / 264
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Transmitter Configuration and Use: Series 1000 and 2000 Transmitters 97
Optional Configuration continued
Required Configuration Optional ConfigurationUsing the TransmitterFlowmeter Startup
8.15.2 Changing the HART polling address
The transmitter’s HART polling address is used by devices on a network to identify
and communicate with the transmitter using HART protocol. The HART polling
address must be unique on the network. If the transmitter will not be accessed using
HART protocol, the HART polling address is not required.
The HART polling address is used for both HART/Bell202 and HART/RS485
communications; i.e., for HART communication over either the primary mA output
terminals or the RS-485 terminals (AN transmitters only).
Note: Devices using HART protocol to communicate with the transmitter may use either the HART
polling address or the HART tag (see Section 8.16) . You may configure either or both, as required by
your other HART devices.
Valid HART polling addresses are 0–15.
Zero is a special-purpose polling address that enables the primary mA output to vary according to the
assigned process variable. When a transmitter’s HART polling address is set to any value other than
zero, the primary mA output is fixed at 4 mA, and will not report any variation in the assigned process
variable.
8.15.3 Changing the Modbus address
The transmitter’s Modbus address is used by devices on a network to identify and
communicate with the transmitter using Modbus protocol. The Modbus address
must be unique on the network. If the transmitter will not be accessed using Modbus
protocol, the Modbus address is not required.
Valid Modbus addresses are:
•1–15
• 32–47
• 64–79
• 96–110
Note: If you are using ProLink II, and you are connected to the transmitter over a Modbus
connection, ProLink II will lose communication as soon as you click the Apply button. To reestablish
communication, you must change the communication settings specified in the ProLink II Connect
dialog box (see Chapter 3). This does not apply to service port connections.
8.15.4 Changing the RS-485 parameters
RS-485 parameters control how the transmitter will communicate over its RS-485
terminals. The RS-485 parameters are listed in Table 8-10.
• Model 1500 AN
• Model 1700 AN
• Model 1700 IS
• Model 2500 CIO
• Model 2700 AN
• Model 2700 IS
• Model 2700 CIO
• Model 1500 AN
• Model 1700 AN
• Model 2500 CIO
• Model 2700 AN
• Model 1500 AN
• Model 1700 AN
• Model 2500 CIO
• Model 2700 AN
- Micro Motion 1
- Series 1000 and 1
- Series 2000 Transmitters 1
- Contents 5
- Chapter 1 11
- Before You Begin 11
- Before You Begin continued 13
- Topic Document 13
- Term Definition 13
- Item Configuration data 15
- Chapter 2 17
- Using the Transmitter Display 17
- –8.100E 5 19
- Chapter 3 21
- Poll button in the Connect 26
- 1 and 2, or to the 26
- Connect to Device 32
- Chapter 4 33
- 375 Field Communicator 33
- Chapter 5 39
- Flowmeter Startup 39
- Flowmeter Startup continued 40
- 5.5.3 Zeroing with ProLink II 50
- Chapter 6 53
- Sensor type 54
- T- S er ie s O t he r 54
- Newer tag Older tag 55
- Flow FCF X.XXXX FT X.XX 56
- Terminals 58
- Default Process 58
- Mass flow unit 60
- Volume flow unit 61
- ProLink II code 69
- Communicator 69
- Polarity 75
- Output power 75
- Description 75
- Assignment ProLink II code 77
- Using the Transmitter 79
- Chapter 7 79
- • Model 1700 AN 84
- • Model 1700 IS 84
- • Model 2700 AN 84
- • Model 2700 IS 84
- • Model 2700 CIO 84
- Scroll optical switch 85
- Select optical switch 85
- Function name Communicator 86
- ProLink II 86
- ProLink 87
- Totalizer Control 87
- With a Communicator 88
- Chapter 8 89
- Optional Configuration 89
- Table 8-1 Configuration map 90
- Special 92
- • Model 2500 CIO 93
- Variable Description 94
- Cutoff type Default Comments 96
- Example 1 100
- Example 2 100
- Example 3 101
- Informational panel of the 102
- Status window 102
- Scroll to view process 104
- Max Int. Totalizers stop 106
- Parameter 109
- Series 1000 Series 2000 110
- Process variable 110
- PV SV TV QV PV SV TV QV 110
- Parameter Description 111
- Chapter 9 113
- Compensation, and Polling 113
- Pressure unit 114
- Static pressure 116
- Polled Var 1 119
- Chapter 10 121
- Troubleshooting 121
- Troubleshooting continued 122
- Section Topic 122
- Symptom Cause Possible remedy 132
- Pickoff value 141
- Cause Possible remedy 141
- Test terminal pair 146
- Colors Numbers 146
- Possible cause Solution 147
- Appendix A 151
- Default Values and Ranges 151
- Appendix B 155
- Appendix C 167
- Calibrating the Transmitter 167
- Appendix D 175
- Name Description 176
- Available process variables 178
- Slope and offset 181
- Appendix E 183
- Other configuration options 185
- Preferences menu 187
- Figure E-4 Communicator menus 188
- Appendix F 193
- Figure F-4 Communicator menus 197
- Appendix G 203
- Transmitters 203
- Figure G-4 Communicator menus 207
- Enter password if required 212
- Appendix H 219
- Figure H-4 Communicator menus 223
- Appendix I 235
- Configuration 237
- Figure I-4 Communicator menus 239
- On-Line Menu 240
- 3 Basic Setup 240
- 4 Detailed Setup 240
- 5 Review 243
- Appendix J 251
- Select to disable 252
- Select to enable 252
- Index continued 256
- *20001715* 264
Powiązane produkty i podręczniki dla Pomiary, testowanie i kontrola Emerson MICRO MOTION 2700
(66 strony)
(3 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.052 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji