Emerson MICRO MOTION 2700 Instrukcja Instalacji Strona 195
- Strona / 264
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Transmitter Configuration and Use: Series 1000 and 2000 Transmitters 185
Menu Flowcharts – Model 2500 CIO Transmitters continued
Enhanced Density Model 2500 CIOModel 1500 ANCalibration
Figure F-2 ProLink II configuration menu (continued)
Configuration
RS-485
•Protocol
• Baud Rate
•Parity
• Stop Bits
Variable mapping
•PV is
•SV is
•TV is
•QV is
Device
•Tag
•Date
• Descriptor
• Message
• Sensor type
• Digital comm fault
setting
• Floating pt ordering
• Add comm resp delay
• Transmitter serial #
Digital comm settings
• Digital comm fault
setting
• Modbus address
• HART address
• HART device ID
Burst setup
• Enable burst
•Burst CMD
•Burst var 1–4
Update rate
• Update rate
• 100 Hz variable
Channel configuration
Channel B
• Type assignment
• Power type
Channel C
• Type assignment
• Power type
Frequency
(1)
• Tertiary variable
• Pulse width
• Last measured value
timeout
• Freq output mode
• Scaling method
• Freq factor
(2)
• Rate factor
(2)
• Pulses per unit
(3)
• Units per pulse
(4)
• Freq fault action
• Freq output polarity
(1) The frequency output options are available only if a channel
has been configured for frequency output.
(2) Displayed only if Scaling method is set to Frequency = flow.
(3) Displayed only if Scaling method is set to Pulses/unit.
(4) Displayed only if Scaling method is set to Units/pulse.
Discrete IO
Discrete output
(1)
• DO1 assignment
• DO2 assignment
•DO1 polarity
•DO2 polarity
• Flow switch setpoint
Discrete input
(2)
• DI assignment
(1) The discrete output options are available only if a channel has
been configured for discrete output.
(2) The discrete input options are available only if a channel has
been configured for discrete input.
- Micro Motion 1
- Series 1000 and 1
- Series 2000 Transmitters 1
- Contents 5
- Chapter 1 11
- Before You Begin 11
- Before You Begin continued 13
- Topic Document 13
- Term Definition 13
- Item Configuration data 15
- Chapter 2 17
- Using the Transmitter Display 17
- –8.100E 5 19
- Chapter 3 21
- Poll button in the Connect 26
- 1 and 2, or to the 26
- Connect to Device 32
- Chapter 4 33
- 375 Field Communicator 33
- Chapter 5 39
- Flowmeter Startup 39
- Flowmeter Startup continued 40
- 5.5.3 Zeroing with ProLink II 50
- Chapter 6 53
- Sensor type 54
- T- S er ie s O t he r 54
- Newer tag Older tag 55
- Flow FCF X.XXXX FT X.XX 56
- Terminals 58
- Default Process 58
- Mass flow unit 60
- Volume flow unit 61
- ProLink II code 69
- Communicator 69
- Polarity 75
- Output power 75
- Description 75
- Assignment ProLink II code 77
- Using the Transmitter 79
- Chapter 7 79
- • Model 1700 AN 84
- • Model 1700 IS 84
- • Model 2700 AN 84
- • Model 2700 IS 84
- • Model 2700 CIO 84
- Scroll optical switch 85
- Select optical switch 85
- Function name Communicator 86
- ProLink II 86
- ProLink 87
- Totalizer Control 87
- With a Communicator 88
- Chapter 8 89
- Optional Configuration 89
- Table 8-1 Configuration map 90
- Special 92
- • Model 2500 CIO 93
- Variable Description 94
- Cutoff type Default Comments 96
- Example 1 100
- Example 2 100
- Example 3 101
- Informational panel of the 102
- Status window 102
- Scroll to view process 104
- Max Int. Totalizers stop 106
- Parameter 109
- Series 1000 Series 2000 110
- Process variable 110
- PV SV TV QV PV SV TV QV 110
- Parameter Description 111
- Chapter 9 113
- Compensation, and Polling 113
- Pressure unit 114
- Static pressure 116
- Polled Var 1 119
- Chapter 10 121
- Troubleshooting 121
- Troubleshooting continued 122
- Section Topic 122
- Symptom Cause Possible remedy 132
- Pickoff value 141
- Cause Possible remedy 141
- Test terminal pair 146
- Colors Numbers 146
- Possible cause Solution 147
- Appendix A 151
- Default Values and Ranges 151
- Appendix B 155
- Appendix C 167
- Calibrating the Transmitter 167
- Appendix D 175
- Name Description 176
- Available process variables 178
- Slope and offset 181
- Appendix E 183
- Other configuration options 185
- Preferences menu 187
- Figure E-4 Communicator menus 188
- Appendix F 193
- Figure F-4 Communicator menus 197
- Appendix G 203
- Transmitters 203
- Figure G-4 Communicator menus 207
- Enter password if required 212
- Appendix H 219
- Figure H-4 Communicator menus 223
- Appendix I 235
- Configuration 237
- Figure I-4 Communicator menus 239
- On-Line Menu 240
- 3 Basic Setup 240
- 4 Detailed Setup 240
- 5 Review 243
- Appendix J 251
- Select to disable 252
- Select to enable 252
- Index continued 256
- *20001715* 264
Powiązane produkty i podręczniki dla Pomiary, testowanie i kontrola Emerson MICRO MOTION 2700
(66 strony)
(3 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.046 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji