Emerson MICRO MOTION 2700 Instrukcja Instalacji Strona 128
- Strona / 264
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
118 Transmitter Configuration and Use: Series 1000 and 2000 Transmitters
Troubleshooting continued
A5 Input over range Input Overrange Check the test points. See Section 10.24.
Check the sensor coils. See Section 10.26.
Verify process.
Make sure that the appropriate measurement unit is
configured. See Section 10.19.
Verify 4 mA and 20 mA values. See Section 10.20.
Verify calibration factors in transmitter configuration.
See Section 6.2.
Re-zero the transmitter.
A6 Field device not
characterized
Not Configured Check the characterization. Specifically, verify the
FCF and K1 values. See Section 6.2.
If the problem persists, contact Micro Motion. See
Section 10.3.
A7 Real time interrupt
failure
RTI Failure Cycle power to the flowmeter.
The flowmeter might need service. Contact Micro
Motion. See Section 10.3.
A8 Density outside limits Density Overrange Check the test points. See Section 10.24.
Check the sensor coils. See Section 10.26.
Verify process. Check for air in the flow tubes, tubes
not filled, foreign material in tubes, or coating in
tubes.
Verify calibration factors in transmitter configuration.
See Section 6.2.
Perform density calibration. See Section C.3.
A9 Field device warming up Transmitter Initializing Allow the flowmeter to warm up. The error should
disappear once the flowmeter is ready for normal
operation.
If alarm does not clear, make sure that the sensor is
completely full or completely empty. Verify sensor
configuration and wiring to sensor.
A10 Calibration failed Calibration Failure If alarm appears during a transmitter zero, ensure
that there is no flow through the sensor, then retry.
Cycle power to the flowmeter, then retry.
A11 Excess calibration
correction, zero too low
Zero too Low Ensure that there is no flow through the sensor, then
retry.
Cycle power to the flowmeter, then retry.
A12 Excess calibration
correction, zero too high
Zero too High Ensure that there is no flow through the sensor, then
retry.
Cycle power to the flowmeter, then retry.
A13 Process too noisy to
perform auto zero
Zero too Noisy Remove or reduce sources of electromechanical
noise, then attempt the calibration or zero procedure
again.
Sources of noise include:
• Mechanical pumps
• Pipe stress at sensor
• Electrical interference
• Vibration effects from nearby machinery
Cycle power to the flowmeter, then retry. See
Section 10.23.
Table 10-5 Status alarms and remedies (continued)
Alarm
code Communicator ProLink II software Possible remedy
- Micro Motion 1
- Series 1000 and 1
- Series 2000 Transmitters 1
- Contents 5
- Chapter 1 11
- Before You Begin 11
- Before You Begin continued 13
- Topic Document 13
- Term Definition 13
- Item Configuration data 15
- Chapter 2 17
- Using the Transmitter Display 17
- –8.100E 5 19
- Chapter 3 21
- Poll button in the Connect 26
- 1 and 2, or to the 26
- Connect to Device 32
- Chapter 4 33
- 375 Field Communicator 33
- Chapter 5 39
- Flowmeter Startup 39
- Flowmeter Startup continued 40
- 5.5.3 Zeroing with ProLink II 50
- Chapter 6 53
- Sensor type 54
- T- S er ie s O t he r 54
- Newer tag Older tag 55
- Flow FCF X.XXXX FT X.XX 56
- Terminals 58
- Default Process 58
- Mass flow unit 60
- Volume flow unit 61
- ProLink II code 69
- Communicator 69
- Polarity 75
- Output power 75
- Description 75
- Assignment ProLink II code 77
- Using the Transmitter 79
- Chapter 7 79
- • Model 1700 AN 84
- • Model 1700 IS 84
- • Model 2700 AN 84
- • Model 2700 IS 84
- • Model 2700 CIO 84
- Scroll optical switch 85
- Select optical switch 85
- Function name Communicator 86
- ProLink II 86
- ProLink 87
- Totalizer Control 87
- With a Communicator 88
- Chapter 8 89
- Optional Configuration 89
- Table 8-1 Configuration map 90
- Special 92
- • Model 2500 CIO 93
- Variable Description 94
- Cutoff type Default Comments 96
- Example 1 100
- Example 2 100
- Example 3 101
- Informational panel of the 102
- Status window 102
- Scroll to view process 104
- Max Int. Totalizers stop 106
- Parameter 109
- Series 1000 Series 2000 110
- Process variable 110
- PV SV TV QV PV SV TV QV 110
- Parameter Description 111
- Chapter 9 113
- Compensation, and Polling 113
- Pressure unit 114
- Static pressure 116
- Polled Var 1 119
- Chapter 10 121
- Troubleshooting 121
- Troubleshooting continued 122
- Section Topic 122
- Symptom Cause Possible remedy 132
- Pickoff value 141
- Cause Possible remedy 141
- Test terminal pair 146
- Colors Numbers 146
- Possible cause Solution 147
- Appendix A 151
- Default Values and Ranges 151
- Appendix B 155
- Appendix C 167
- Calibrating the Transmitter 167
- Appendix D 175
- Name Description 176
- Available process variables 178
- Slope and offset 181
- Appendix E 183
- Other configuration options 185
- Preferences menu 187
- Figure E-4 Communicator menus 188
- Appendix F 193
- Figure F-4 Communicator menus 197
- Appendix G 203
- Transmitters 203
- Figure G-4 Communicator menus 207
- Enter password if required 212
- Appendix H 219
- Figure H-4 Communicator menus 223
- Appendix I 235
- Configuration 237
- Figure I-4 Communicator menus 239
- On-Line Menu 240
- 3 Basic Setup 240
- 4 Detailed Setup 240
- 5 Review 243
- Appendix J 251
- Select to disable 252
- Select to enable 252
- Index continued 256
- *20001715* 264
Powiązane produkty i podręczniki dla Pomiary, testowanie i kontrola Emerson MICRO MOTION 2700
(66 strony)
(3 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.050 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji